410039, г. Саратов, ул. Барнаульская д.11Тел./факс: +7 ( 927) 161 – 36 - 65, 70-03-44e-mail: remontprinterov@mail.ru
|
Коды ошибок
|
|
Код ошибки |
Описание |
|
C1 |
Copy table position error |
|
C2 |
Paper is not fed from the tray when the copy table starts moving |
|
C3 |
Copy table drive error |
|
C4 |
Copy table position error |
|
C5 |
Copy table end position error |
|
C6 |
Copy table position error at the end of the copy cycle |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
C8 |
Thermofuse blown |
|
CP |
Main drive overloaded |
|
CA |
Main Board defective |
|
E1 |
Paper jam |
|
E2 |
Fuser jam |
|
E3 |
Paper jam at start-up |
|
E5 |
Paper jam in the tray |
|
E7 |
Paper jam in the registration area |
Toshiba 1310
|
Код ошибки |
Описание |
|
C5 |
Copy table drive overloaded |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
CE |
EPROM defective or missing |
|
CP |
Main drive overloaded |
|
CD |
EPROM end of life |
|
CF |
Development unit not properly installed or defective |
|
E0 |
Used toner collection bottle full |
|
E1 |
Paper jam |
|
E2 |
Fuser jam |
|
E3 |
Paper jam at start-up |
|
E5 |
Paper jam in the tray |
|
E6 |
Paper jam at by-pass or defective sensor |
Toshiba 1340, 1350
|
Код ошибки |
Описание |
|
C5, C6 |
Scan problem |
|
C7 |
Fuser problem (reset with 0 + 8 mode, code 89) |
|
CE |
Missing EEPROM |
|
CF |
Board problem |
|
CP |
Drive problem |
|
E1 |
Paper jam |
|
E2 |
Fuser jam |
|
E3 |
Paper jam |
|
E5 |
Paper feed jam |
|
E0 |
Toner waste bottle is full |
Toshiba 1550
|
Код ошибки |
Описание |
|
C01 |
Main motor drive problem |
|
C21 |
Optics problem Scan , lens, mirror |
|
C26 |
Exposure lamp detect problem |
|
C32 |
Setup error (UA) |
|
C41 |
Fuser thermistor, or no heat |
|
C43 |
Fuser thermistor problem or other fuser problem, after machine goes into ready |
|
C44 |
Heater problem |
|
C54 |
Communication problem between sorter and machine main board |
|
C55 |
Communication problem between ADF and machine main board |
|
C71 |
ADF drive problem |
|
C72 |
ADF registration sensor problem |
|
C73 |
EEPROM initialization problem |
|
C81 |
Sorter paper conveying motor |
|
C82 |
Sorter bin motor |
|
C83 |
Sorter upper sensor |
|
C84 |
Sorter lower sensor |
|
C85 |
Sorter home sensor |
|
C86 |
Sorter copy removal sensor |
|
C94 |
Optics initialization problem in test modes |
|
E01 |
Paper jam |
|
E02 |
Fuser jam |
|
E03 |
Paper jam at startup |
|
E05 |
Paper jam in the registration area |
|
E14 |
Lower cassette jam |
|
E71, E72, E73 |
ADF jam |
|
E75 |
ADF jam of 2nd original |
|
E81, E82 |
Sorter jam |
Toshiba 1560
|
Код ошибки |
Описание |
|
C01 |
Main motor drive overloaded |
|
C21 |
Optics problem Scan , lens, mirror |
|
C26 |
Exposure lamp blown, or bad contacts |
|
C32 |
Easy set-up error |
|
C41 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
C43, C44 |
Abnormal temperature in the fuser, thermistor error |
|
C54 |
Communication with the sorter is intrerrupted |
|
C55 |
Communication with the feeder is intrerrupted |
|
C71 |
Top Feeder motor overloaded |
|
C72 |
Sensor problem in the feeder |
|
C73 |
Feeder EPROM initialization error |
|
C81 |
Sorter paper transport motor overloaded |
|
C82 |
Sorter shift tray motor overloaded |
|
C83 |
Upper position error in the sorter |
|
C84 |
Lower limit position error in the sorter |
|
C85 |
Home position error in sorter |
|
C88 |
Paper sensor error in sorter |
|
C94 |
Optical system initialization error |
|
E01 |
Paper jam |
|
E02 |
Fuser jam |
|
E03 |
Paper jam at startup |
|
E05 |
Paper jam in the registration area |
|
E14 |
Paper jam in the Paper Feed Unit |
|
E71 |
Original jammed in the top feeder |
|
E72 |
Original jammed during transport in the top feeder |
|
E73 |
Original jam at the feeder exit |
|
E75 |
Original jammed |
|
E81, E82 |
Sorter jam |
Toshiba 1650
|
Код ошибки |
Описание |
|
A4 |
Sorter problem |
|
A5 |
Communication problem between main CPU and IPC |
|
A6 |
Sorter interface problem |
|
C2 |
Communication problem between CPU's |
|
C5 |
Scan or optic problem. Locked up or won't initialize or return to home position |
|
C7 |
Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset |
|
CF |
Developer calibration problem |
|
CP |
Drive problem |
|
E1 |
Paper jam |
|
E2 |
Fuser jam |
|
E3 |
Paper jam |
|
E4 |
Front door opened during copy cycle |
|
E5 |
Paper feed jam |
Toshiba 1710
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
ADD problem |
|
A4 |
Sorter problem |
|
A5 |
Board problem |
|
A6 |
Sorter board problem |
|
A7 |
ADF interface |
|
A0 |
Communication problem between main board and PFC |
|
C1 |
Board problem |
|
C2 |
Board problem |
|
C3 |
Board problem |
|
C4 |
Board problem |
|
C5 |
Optics locked or not initialized. Could be scan or lens/mirror |
|
C7 |
Fuser thermistoe problem, or low temperature |
|
C8 |
Scan motor won't shut off |
|
CA |
Main board problem |
|
CB |
ADF drive problem |
|
CC |
ADF drive problem |
|
CD |
BC RAM hardware |
|
CE |
BC RAM software |
|
CP |
Drive problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
E8 |
Jam in ADD (duplex) |
|
E9 |
Jam in pedestal |
|
EC |
ADF jam |
|
ED |
ADF jam |
|
EE |
ADF exit/reverse jam |
Toshiba 2050
|
Код ошибки |
Описание |
|
A4 |
Sorter problem |
|
A5 |
Communication problem between main CPU and IPC |
|
A6 |
Sorter interface problem |
|
C2 |
Communication problem between CPU's |
|
C5 |
Scan or optic problem. Locked up or won't initialize or return to home position |
|
C7 |
Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset |
|
CF |
Developer calibration problem |
|
CP |
Drive problem |
|
E1 |
Paper jam |
|
E2 |
Fuser jam |
|
E3 |
Paper jam |
|
E4 |
Front door opened during copy cycle |
|
E5 |
Paper feed jam |
Toshiba 2060
|
Код ошибки |
Описание |
|
C01 |
Main motor drive problem |
|
C04 |
Pedestal main drive problem |
|
C05 |
Duplex drive problem |
|
C11 |
Duplex exit motor |
|
C12 |
Duplex end motor |
|
C13 |
Upper cassette |
|
C14 |
Lower cassette |
|
C15 |
Pedestal upper cassette |
|
C16 |
Pedestal middle cassette |
|
C17 |
Pedestal lower cassette |
|
C18 |
LCT |
|
C21 |
Scan problem |
|
C22 |
Lens problem |
|
C23 |
Mirror motor |
|
C26 |
Exposure lamp |
|
C27 |
Scan motor |
|
C33 |
Set up failure |
|
C35 |
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona |
|
C41 |
Fuser thermistor or low temperature |
|
C43 |
Fuser problem after warm-up |
|
C44 |
Fuser problem after warm-up |
|
C45 |
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time |
|
E01 |
Jam |
|
E02 |
Fuser jam |
|
E03 |
Jam at turn on |
|
E04 |
Front door opened during copy cycle |
|
E05 |
Registration jam |
|
E08 |
Duplex unit jam |
|
E11 |
Duplex jam |
|
E12 |
Bypass jam |
|
E13 |
Upper cassette jam |
|
E14 |
2nd cassette jam |
|
E15 |
3rd cassette jam |
|
E16 |
4th cassette jam |
|
E17 |
4th cassette jam |
|
E19 |
CT jam |
|
E21 |
LCT jam |
|
E22-E25 |
Paper jams in copier |
|
E71 |
ADF feed jam |
|
E72 |
ADF transport jam |
|
E73 |
ADF exit jam |
|
E74 |
RADF jam |
|
E75 |
ADF 2nd original jam |
|
E81-E85 |
Sorter jam |
|
E88 |
Jam after sorter |
Toshiba 2310
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
ADD problem |
|
A4 |
Sorter problem |
|
A5 |
Board problem |
|
A6 |
Sorter board problem |
|
A7 |
ADF interface |
|
A0 |
Communication problem between main board and PFC |
|
C1 |
Board problem |
|
C2 |
Board problem |
|
C3 |
Board problem |
|
C4 |
Board problem |
|
C5 |
Optics locked or not initialized. Could be scan or lens/mirror |
|
C7 |
Fuser thermistoe problem, or low temperature |
|
C8 |
Scan motor won't shut off |
|
CA |
Main board problem |
|
CB |
ADF drive problem |
|
CC |
ADF drive problem |
|
CD |
BC RAM hardware |
|
CE |
BC RAM software |
|
CP |
Drive problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
E8 |
Jam in ADD (duplex) |
|
E9 |
Jam in pedestal |
|
EC |
ADF jam |
|
ED |
ADF jam |
|
EE |
ADF exit/reverse jam |
Toshiba 2500
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
ADD problem |
|
A4 |
Sorter problem |
|
A5 |
Board problem |
|
A6 |
Sorter board problem |
|
A7 |
ADF interface |
|
A0 |
Communication problem between main board and PFC |
|
C1 |
Board problem |
|
C2 |
Board problem |
|
C3 |
Board problem |
|
C4 |
Board problem |
|
C5 |
Optics locked or not initialized. Could be scan or lens/mirror |
|
C7 |
Fuser thermistoe problem, or low temperature |
|
C8 |
Scan motor won't shut off |
|
CA |
Main board problem |
|
CB |
ADF drive problem |
|
CC |
ADF drive problem |
|
CD |
BC RAM hardware |
|
CE |
BC RAM software |
|
CP |
Drive problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
E8 |
Jam in ADD (duplex) |
|
E9 |
Jam in pedestal |
|
EC |
ADF jam |
|
ED |
ADF jam |
|
EE |
ADF exit/reverse jam |
Toshiba 2510
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
ADD problem |
|
A4 |
Sorter problem |
|
A5 |
Board problem |
|
A6 |
Sorter board problem |
|
A7 |
ADF interface |
|
A0 |
Communication problem between main board and PFC |
|
C1 |
Board problem |
|
C2 |
Board problem |
|
C3 |
Board problem |
|
C4 |
Board problem |
|
C5 |
Optics locked or not initialized. Could be scan or lens/mirror |
|
C7 |
Fuser thermistoe problem, or low temperature |
|
C8 |
Scan motor won't shut off |
|
CA |
Main board problem |
|
CB |
ADF drive problem |
|
CC |
ADF drive problem |
|
CD |
BC RAM hardware |
|
CE |
BC RAM software |
|
CP |
Drive problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
E8 |
Jam in ADD (duplex) |
|
E9 |
Jam in pedestal |
|
EC |
ADF jam |
|
ED |
ADF jam |
|
EE |
ADF exit/reverse jam |
Toshiba 2532
|
Код ошибки |
Описание |
|
A4 |
Sorter problem |
|
A5 |
Communication problem with main board |
|
A6 |
Communication problem with sorter |
|
A7 |
Communication problem with ADF |
|
A9 |
Exposure lamp problem or auto exposure problem |
|
C2 |
Communication problem between main board |
|
C5 |
Scan won't initialize or won't move |
|
C7 |
Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89 |
|
CC |
ADF belt motor or exit motor not turning |
|
CF |
Auto toner adjustment did not take |
|
CP |
Drive problem in machine |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy cycle |
|
E5 |
Feed jam |
Toshiba 2540
|
Код ошибки |
Описание |
|
A4 |
Sorter problem |
|
A5 |
Communication problem with main board |
|
A6 |
Communication problem with sorter |
|
A7 |
Communication problem with ADF |
|
A9 |
Exposure lamp problem or auto exposure problem |
|
C2 |
Communication problem between main board |
|
C5 |
Scan won't initialize or won't move |
|
C7 |
Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89 |
|
CC |
ADF belt motor or exit motor not turning |
|
CF |
Auto toner adjustment did not take |
|
CP |
Drive problem in machine |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy cycle |
|
E5 |
Feed jam |
Toshiba 2550
|
Код ошибки |
Описание |
|
A2 |
Duplex functional problems |
|
A4 |
Sorter problem |
|
A5 |
Communication lost with the sorter |
|
A6 |
Communication problems with the sorter interface |
|
A7 |
Communication problems with the feeder |
|
A9 |
Exposure lamp blown, or bad contacts |
|
C2, C3 |
Processor to subprocessor communication problems |
|
C5 |
Optical system initialization error |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
CB |
Original feed motor overloaded in the feeder |
|
CC |
Original transport motor overloaded in the feeder |
|
CF |
Toner density error |
|
CP |
Main motor drive overloaded |
|
E1 |
Paper jam detected in machine |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Paper jam at start-up |
|
E4 |
Front cover open during copy cicle |
|
E5 |
Paper feed jam in the paper tray |
|
E8 |
Paper jam in the duplex unit |
|
E9 |
Paper jam in the optional paper feed unit |
|
EC |
Original misfeed in the feeder |
|
ED |
Original jam in the feeder |
|
EE |
Original jam at the feeder inverter or exit area |
Toshiba 2810
|
Код ошибки |
Описание |
|
C1 |
Scan did not return home |
|
C3 |
Scan home sensor |
|
C4 |
Scan problem |
|
C5 |
Scan limit sensor |
|
C6 |
Scan did not return |
|
C7 |
Thermistor or other fuser problem |
|
CC |
Scan did not leave home |
|
CP |
Drive |
|
E1 |
Jam inside machine |
|
E2 |
Fuser jam or exit jam |
|
E3 |
Exit switch or registration switch |
|
E5 |
Paper feed jam |
|
E7 |
Cassette or registration jam |
Toshiba 2860
|
Код ошибки |
Описание |
|
C01 |
Main motor drive problem |
|
C04 |
Pedestal main drive problem |
|
C05 |
Duplex drive problem |
|
C11 |
Duplex exit motor |
|
C12 |
Duplex end motor |
|
C13 |
Upper cassette |
|
C14 |
Lower cassette |
|
C15 |
Pedestal upper cassette |
|
C16 |
Pedestal middle cassette |
|
C17 |
Pedestal lower cassette |
|
C18 |
LCT |
|
C21 |
Scan problem |
|
C22 |
Lens problem |
|
C23 |
Mirror motor |
|
C26 |
Exposure lamp |
|
C27 |
Scan motor |
|
C33 |
Set up failure |
|
C35 |
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona |
|
C41 |
Fuser thermistor or low temperature |
|
C43 |
Fuser problem after warm-up |
|
C44 |
Fuser problem after warm-up |
|
C45 |
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time |
|
E01 |
Jam |
|
E02 |
Fuser jam |
|
E03 |
Jam at turn on |
|
E04 |
Front door opened during copy cycle |
|
E05 |
Registration jam |
|
E08 |
Duplex unit jam |
|
E11 |
Duplex jam |
|
E12 |
Bypass jam |
|
E13 |
Upper cassette jam |
|
E14 |
2nd cassette jam |
|
E15 |
3rd cassette jam |
|
E16 |
4th cassette jam |
|
E17 |
4th cassette jam |
|
E19 |
CT jam |
|
E21 |
LCT jam |
|
E22-E25 |
Paper jams in copier |
|
E71 |
ADF feed jam |
|
E72 |
ADF transport jam |
|
E73 |
ADF exit jam |
|
E74 |
RADF jam |
|
E75 |
ADF 2nd original jam |
|
E81-E85 |
Sorter jam |
|
E88 |
Jam after sorter |
Toshiba 2870
|
Код ошибки |
Описание |
|
C01 |
Main motor drive problem |
|
C04 |
Pedestal main drive problem |
|
C05 |
Duplex drive problem |
|
C11 |
Duplex exit motor |
|
C12 |
Duplex end motor |
|
C13 |
Upper cassette |
|
C14 |
Lower cassette |
|
C15 |
Pedestal upper cassette |
|
C16 |
Pedestal middle cassette |
|
C17 |
Pedestal lower cassette |
|
C18 |
LCT |
|
C21 |
Scan problem |
|
C22 |
Lens problem |
|
C23 |
Mirror motor |
|
C26 |
Exposure lamp |
|
C27 |
Scan motor |
|
C33 |
Set up failure |
|
C35 |
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona |
|
C41 |
Fuser thermistor or low temperature |
|
C43 |
Fuser problem after warm-up |
|
C44 |
Fuser problem after warm-up |
|
C45 |
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time |
|
E01 |
Jam |
|
E02 |
Fuser jam |
|
E03 |
Jam at turn on |
|
E04 |
Front door opened during copy cycle |
|
E05 |
Registration jam |
|
E08 |
Duplex unit jam |
|
E11 |
Duplex jam |
|
E12 |
Bypass jam |
|
E13 |
Upper cassette jam |
|
E14 |
2nd cassette jam |
|
E15 |
3rd cassette jam |
|
E16 |
4th cassette jam |
|
E17 |
4th cassette jam |
|
E19 |
CT jam |
|
E21 |
LCT jam |
|
E22-E25 |
Paper jams in copier |
|
E71 |
ADF feed jam |
|
E72 |
ADF transport jam |
|
E73 |
ADF exit jam |
|
E74 |
RADF jam |
|
E75 |
ADF 2nd original jam |
|
E81-E85 |
Sorter jam |
|
E88 |
Jam after sorter |
Toshiba 3110
|
Код ошибки |
Описание |
|
C1 |
Copy table start-up position error |
|
C2 |
The paper does not feed when the copy table starts moving |
|
C3 |
Paper start position not detected, copy table switch defective |
|
C4 |
Copy table home position error |
|
C5 |
Copy table end position error |
|
C6 |
Copy table reverse movement error |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
CP |
Main motor drive overloaded |
|
E1 |
Paper jam in the machine |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Paper jam at start-up |
|
E5 |
Paper jam in the paper tray |
|
E6 |
Paper jam at by-pass or defective sensor |
|
E7 |
Paper jam in the feed area or registration |
Toshiba 3210
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
ADD problem |
|
A4 |
Sorter problem |
|
A5 |
Board problem |
|
A6 |
Sorter board problem |
|
A7 |
ADF interface |
|
A0 |
Communication problem between main board and PFC |
|
C1 |
Board problem |
|
C2, C3 |
Processor to subprocessor communication problems |
|
C4 |
Board problem |
|
C5 |
Optics locked or not initialized. Could be scan or lens/mirror |
|
C7 |
Fuser thermistoe problem, or low temperature |
|
C8 |
Scan motor won't shut off |
|
CA |
Main board problem |
|
CB |
ADF drive problem |
|
CC |
ADF drive problem |
|
CD |
BC RAM hardware |
|
CE |
BC RAM software |
|
CP |
Drive problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
E8 |
Jam in ADD (duplex) |
|
E9 |
Jam in pedestal |
|
EC |
ADF jam |
|
ED |
ADF jam |
|
EE |
ADF exit/reverse jam |
Toshiba 3220
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
ADD problem |
|
A4 |
Sorter problem |
|
A5 |
Board problem |
|
A6 |
Sorter board problem |
|
A7 |
ADF interface |
|
A0 |
Communication problem between main board and PFC |
|
C1 |
Board problem |
|
C2 |
Board problem |
|
C3 |
Board problem |
|
C4 |
Board problem |
|
C5 |
Optics locked or not initialized. Could be scan or lens/mirror |
|
C7 |
Fuser thermistoe problem, or low temperature |
|
C8 |
Scan motor won't shut off |
|
CA |
Main board problem |
|
CB |
ADF drive problem |
|
CC |
ADF drive problem |
|
CD |
BC RAM hardware |
|
CE |
BC RAM software |
|
CP |
Drive problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
E8 |
Jam in ADD (duplex) |
|
E9 |
Jam in pedestal |
|
EC |
ADF jam |
|
ED |
ADF jam |
|
EE |
ADF exit/reverse jam |
Toshiba 3301
|
Код ошибки |
Описание |
|
C1 |
Copy table start-up position error |
|
C2 |
The paper does not feed when the copy table starts moving |
|
C3 |
Paper start position not detected, copy table switch defective |
|
C4 |
Copy table home position error |
|
C5 |
Copy table end position error |
|
C6 |
Copy table reverse movement error |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
CP |
Main motor drive overloaded |
|
E1 |
Paper jam in the machine |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Paper jam at start-up |
|
E5 |
Paper jam in the paper tray |
|
E6 |
Paper jam at by-pass or defective sensor |
|
E7 |
Paper jam in the feed area or registration |
Toshiba 3550
|
Код ошибки |
Описание |
|
A1 |
Transfer/separator |
|
A2 |
Duplex problem |
|
A3 |
PFC CPU malfunction |
|
A4 |
Sorter problem |
|
A5 |
Communication problem between main board and IPC |
|
A6 |
Sorter board to copier communication problem |
|
A7 |
Communication problem between copier and RADF |
|
A0 |
Communication main board problem |
|
C3 |
Communication problem between main board and sub processor |
|
C5 |
Optics locked or not initialized |
|
C7 |
Fuser problem. Reset required. Turn off power. Hold "0" & "8" keys while turning on power. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the number keys, press "0". Then press "interrupt". Then press "0" & "9" at the same time |
|
CB |
ADF feed motor drive problem |
|
CC |
ADF transport motor drive problem |
|
CP |
Copier main motor drive problem |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam at turn on |
|
E4 |
Front door opened during copy cycle |
|
E5 |
Registration jam |
|
E8 |
Duplex unit jam |
|
E9 |
Jam in paper feed unit pedistal |
|
EC |
ADF jam |
|
ED |
ADF transport jam |
|
EE |
ADF exit or reversing jam |
Toshiba 3560
|
Код ошибки |
Описание |
|
C01 |
Main motor drive problem |
|
C04 |
Pedestal main drive problem |
|
C05 |
Duplex drive problem |
|
C11 |
Duplex exit motor |
|
C12 |
Duplex end motor |
|
C13 |
Upper cassette |
|
C14 |
Lower cassette |
|
C15 |
Pedestal upper cassette |
|
C16 |
Pedestal middle cassette |
|
C17 |
Pedestal lower cassette |
|
C18 |
LCT |
|
C21 |
Scan problem |
|
C22 |
Lens problem |
|
C23 |
Mirror motor |
|
C26 |
Exposure lamp |
|
C27 |
Scan motor |
|
C33 |
Set up failure |
|
C35 |
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona |
|
C41 |
Fuser thermistor or low temperature |
|
C43 |
Fuser problem after warm-up |
|
C44 |
Fuser problem after warm-up |
|
C45 |
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time |
|
E01 |
Jam |
|
E02 |
Fuser jam |
|
E03 |
Jam at turn on |
|
E04 |
Front door opened during copy cycle |
|
E05 |
Registration jam |
|
E08 |
Duplex unit jam |
|
E11 |
Duplex jam |
|
E12 |
Bypass jam |
|
E13 |
Upper cassette jam |
|
E14 |
2nd cassette jam |
|
E15 |
3rd cassette jam |
|
E16 |
4th cassette jam |
|
E17 |
4th cassette jam |
|
E19 |
CT jam |
|
E21 |
LCT jam |
|
E22-E25 |
Paper jams in copier |
|
E71 |
ADF feed jam |
|
E72 |
ADF transport jam |
|
E73 |
ADF exit jam |
|
E74 |
RADF jam |
|
E75 |
ADF 2nd original jam |
|
E81-E85 |
Sorter jam |
|
E88 |
Jam after sorter |
Toshiba 3570
|
Код ошибки |
Описание |
|
C01 |
Main motor drive problem |
|
C04 |
Pedestal main drive problem |
|
C05 |
Duplex drive problem |
|
C11 |
Duplex exit motor |
|
C12 |
Duplex end motor |
|
C13 |
Upper cassette |
|
C14 |
Lower cassette |
|
C15 |
Pedestal upper cassette |
|
C16 |
Pedestal middle cassette |
|
C17 |
Pedestal lower cassette |
|
C18 |
LCT |
|
C21 |
Scan problem |
|
C22 |
Lens problem |
|
C23 |
Mirror motor |
|
C26 |
Exposure lamp |
|
C27 |
Scan motor |
|
C33 |
Set up failure |
|
C35 |
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona |
|
C41 |
Fuser thermistor or low temperature |
|
C43 |
Fuser problem after warm-up |
|
C44 |
Fuser problem after warm-up |
|
C45 |
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time |
|
E01 |
Jam |
|
E02 |
Fuser jam |
|
E03 |
Jam at turn on |
|
E04 |
Front door opened during copy cycle |
|
E05 |
Registration jam |
|
E08 |
Duplex unit jam |
|
E11 |
Duplex jam |
|
E12 |
Bypass jam |
|
E13 |
Upper cassette jam |
|
E14 |
2nd cassette jam |
|
E15 |
3rd cassette jam |
|
E16 |
4th cassette jam |
|
E17 |
4th cassette jam |
|
E19 |
CT jam |
|
E21 |
LCT jam |
|
E22-E25 |
Paper jams in copier |
|
E71 |
ADF feed jam |
|
E72 |
ADF transport jam |
|
E73 |
ADF exit jam |
|
E74 |
RADF jam |
|
E75 |
ADF 2nd original jam |
|
E81-E85 |
Sorter jam |
|
E88 |
Jam after sorter |
Toshiba 3701
|
Код ошибки |
Описание |
|
E0 |
Paper jammed in the machine at power-up |
|
E1 |
Paper jam in the fusing or transport area |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Misfeed at the manual feed table |
|
E6, E7, E8 |
Copy table drive problem |
|
E9 |
Copy table reverse clutch not working |
Toshiba 3810
|
Код ошибки |
Описание |
|
C5 |
Scan problem |
|
C7 |
Heater problem |
|
CD |
EEPROM at end of life |
|
CE |
EEPROM/main board problem |
|
CF |
DV unit out or toner sensor problem |
|
CP |
Drive |
|
E1 |
Paper jam before exit |
|
E2 |
Exit jam |
|
E3 |
Jam |
|
E5 |
Cassette jam |
|
E6 |
Bypass jam |
|
E0 |
Waste toner full |
Toshiba 3910
|
Код ошибки |
Описание |
|
C5 |
Scan problem |
|
C7 |
Heater problem |
|
CD |
EEPROM at end of life |
|
CE |
EEPROM/main board problem |
|
CF |
DV unit out or toner sensor problem |
|
CP |
Drive |
|
E1 |
Paper jam before exit |
|
E2 |
Exit jam |
|
E3 |
Jam |
|
E5 |
Cassette jam |
|
E6 |
Bypass jam |
|
E0 |
Waste toner full |
Toshiba 4010
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
ADD problem |
|
A4 |
Sorter problem |
|
A5 |
Board problem |
|
A6 |
Sorter board problem |
|
A7 |
ADF interface |
|
A0 |
Communication problem between main board and PFC |
|
C1 |
Board problem |
|
C2 |
Board problem |
|
C3 |
Board problem |
|
C4 |
Board problem |
|
C5 |
Optics locked or not initialized. Could be scan or lens/mirror |
|
C7 |
Fuser thermistoe problem, or low temperature |
|
C8 |
Scan motor won't shut off |
|
CA |
Main board problem |
|
CB |
ADF drive problem |
|
CC |
ADF drive problem |
|
CD |
BC RAM hardware |
|
CE |
BC RAM software |
|
CP |
Drive problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
E8 |
Jam in ADD (duplex) |
|
E9 |
Jam in pedestal |
|
EC |
ADF jam |
|
ED |
ADF jam |
|
EE |
ADF exit/reverse jam |
Toshiba 4111, 4121
|
Код ошибки |
Описание |
|
C1 |
Scanner not home |
|
C2 |
First paper path switch or sub processor |
|
C5 |
Scan stop switch |
|
C5 |
Scan won't stop |
|
C7 |
Fuser problem |
|
C8 |
Lens |
|
C9 |
Check 24V |
Toshiba 4130, 4140
|
Код ошибки |
Описание |
|
C1 |
Copy table reverse movement home position error |
|
C2 |
Paper start position not detected, copy table switch defective |
|
C5 |
Copy table end position error |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
C8 |
Lens home position error |
|
C9 |
5v power supply defective |
|
E1 |
Paper jam detected in machine |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Paper jam at start-up |
|
E5 |
Paper feed jam in the paper tray |
|
E7 |
Paper jam at registration |
Toshiba 4501
|
Код ошибки |
Описание |
|
E0 |
Paper jammed in the machine at power-up |
|
E1 |
Paper jam in the fusing or transport area |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Misfeed at the manual feed table |
|
E6, E7, E8 |
Copy table drive problem |
|
E9 |
Copy table reverse clutch not working |
Toshiba 4550
|
Код ошибки |
Описание |
|
A2 |
Duplex functional problems |
|
A4 |
Sorter problems |
|
A5 |
Communication lost with the sorter |
|
A6 |
Communication problems with the sorter interface |
|
A7 |
Communication problems with the feeder |
|
A9 |
Exposure lamp blown, or bad contacts |
|
C2, C3 |
Processor to subprocessor communication problems |
|
C5 |
Optical system initialization error |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
CB |
Original feed motor overloaded in the feeder |
|
CC |
Original transport motor overloaded in the feeder |
|
CF |
Toner density error |
|
CP |
Main motor drive overloaded |
|
E1 |
Paper jam detected in machine |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Paper jam at start-up |
|
E4 |
Front cover open during copy cicle |
|
E5 |
Paper feed jam in the paper tray |
|
E8 |
Paper jam in the duplex unit |
|
E9 |
Paper jam in the optional paper feed unit |
|
EC |
Original misfeed in the feeder |
|
ED |
Original jam in the feeder |
|
EE |
Original jam at the feeder inverter or exit area |
Toshiba 4560
|
Код ошибки |
Описание |
|
C01 |
Main motor drive problem |
|
C04 |
Pedestal main drive problem |
|
C05 |
Duplex drive problem |
|
C11 |
Duplex exit motor |
|
C12 |
Duplex end motor |
|
C13 |
Upper cassette |
|
C14 |
Lower cassette |
|
C15 |
Pedestal upper cassette |
|
C16 |
Pedestal middle cassette |
|
C17 |
Pedestal lower cassette |
|
C18 |
LCT |
|
C21 |
Scan problem |
|
C22 |
Lens problem |
|
C23 |
Mirror motor |
|
C26 |
Exposure lamp |
|
C27 |
Scan motor |
|
C33 |
Set up failure |
|
C35 |
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona |
|
C41 |
Fuser thermistor or low temperature |
|
C43 |
Fuser problem after warm-up |
|
C44 |
Fuser problem after warm-up |
|
C45 |
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time |
|
E01 |
Jam |
|
E02 |
Fuser jam |
|
E03 |
Jam at turn on |
|
E04 |
Front door opened during copy cycle |
|
E05 |
Registration jam |
|
E08 |
Duplex unit jam |
|
E11 |
Duplex jam |
|
E12 |
Bypass jam |
|
E13 |
Upper cassette jam |
|
E14 |
2nd cassette jam |
|
E15 |
3rd cassette jam |
|
E16 |
4th cassette jam |
|
E17 |
4th cassette jam |
|
E19 |
CT jam |
|
E21 |
LCT jam |
|
E22-E25 |
Paper jams in copier |
|
E71 |
ADF feed jam |
|
E72 |
ADF transport jam |
|
E73 |
ADF exit jam |
|
E74 |
RADF jam |
|
E75 |
ADF 2nd original jam |
|
E81-E85 |
Sorter jam |
|
E88 |
Jam after sorter |
Toshiba 4570
|
Код ошибки |
Описание |
|
C01 |
Main motor drive problem |
|
C04 |
Pedestal main drive problem |
|
C05 |
Duplex drive problem |
|
C11 |
Duplex exit motor |
|
C12 |
Duplex end motor |
|
C13 |
Upper cassette |
|
C14 |
Lower cassette |
|
C15 |
Pedestal upper cassette |
|
C16 |
Pedestal middle cassette |
|
C17 |
Pedestal lower cassette |
|
C18 |
LCT |
|
C21 |
Scan problem |
|
C22 |
Lens problem |
|
C23 |
Mirror motor |
|
C26 |
Exposure lamp |
|
C27 |
Scan motor |
|
C33 |
Set up failure |
|
C35 |
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona |
|
C41 |
Fuser thermistor or low temperature |
|
C43 |
Fuser problem after warm-up |
|
C44 |
Fuser problem after warm-up |
|
C45 |
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time |
|
E01 |
Jam |
|
E02 |
Fuser jam |
|
E03 |
Jam at turn on |
|
E04 |
Front door opened during copy cycle |
|
E05 |
Registration jam |
|
E08 |
Duplex unit jam |
|
E11 |
Duplex jam |
|
E12 |
Bypass jam |
|
E13 |
Upper cassette jam |
|
E14 |
2nd cassette jam |
|
E15 |
3rd cassette jam |
|
E16 |
4th cassette jam |
|
E17 |
4th cassette jam |
|
E19 |
CT jam |
|
E21 |
LCT jam |
|
E22-E25 |
Paper jams in copier |
|
E71 |
ADF feed jam |
|
E72 |
ADF transport jam |
|
E73 |
ADF exit jam |
|
E74 |
RADF jam |
|
E75 |
ADF 2nd original jam |
|
E81-E85 |
Sorter jam |
|
E88 |
Jam after sorter |
Toshiba 4810
|
Код ошибки |
Описание |
|
C1 |
Scan not home |
|
C2 |
Scan did not leave home |
|
C3 |
Forward scan |
|
C4 |
Forward scan (dual page mode) |
|
C5 |
Scan limit |
|
C6 |
Scan return |
|
C7 |
Thermistor |
|
CP |
Motor lock |
|
E1 |
Fuser jam |
|
E2 |
Exit jam |
|
E3 |
Jam |
|
E5, E7 |
PF jam |
Toshiba 4910
|
Код ошибки |
Описание |
|
C4 |
Cam switch |
|
C5 |
Optics |
|
C7 |
Thermistor or fuser |
|
C8 |
Scan motor stays on |
|
CE |
Main board |
|
C0 |
Dead battery |
|
CP |
Drive |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam at turn on |
|
E4 |
Door opened during copy run |
Toshiba 5010
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
ADD problem |
|
A4 |
Sorter problem |
|
A5 |
Board problem |
|
A6 |
Sorter board problem |
|
A7 |
ADF interface |
|
A0 |
Communication problem between main board and PFC |
|
C1 |
Board problem |
|
C2 |
Board problem |
|
C3 |
Board problem |
|
C4 |
Board problem |
|
C5 |
Optics locked or not initialized. Could be scan or lens/mirror |
|
C7 |
Fuser thermistoe problem, or low temperature |
|
C8 |
Scan motor won't shut off |
|
CA |
Main board problem |
|
CB |
ADF drive problem |
|
CC |
ADF drive problem |
|
CD |
BC RAM hardware |
|
CE |
BC RAM software |
|
CP |
Drive problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
E8 |
Jam in ADD (duplex) |
|
E9 |
Jam in pedestal |
|
EC, ED |
ADF jam |
|
EE |
ADF exit/reverse jam |
Toshiba 5020
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
ADD problem |
|
A4 |
Sorter problem |
|
A5 |
Board problem |
|
A6 |
Sorter board problem |
|
A7 |
ADF interface |
|
A0 |
Communication problem between main board and PFC |
|
C1 |
Board problem |
|
C2 |
Board problem |
|
C3 |
Board problem |
|
C4 |
Board problem |
|
C5 |
Optics locked or not initialized. Could be scan or lens/mirror |
|
C7 |
Fuser thermistoe problem, or low temperature |
|
C8 |
Scan motor won't shut off |
|
CA |
Main board problem |
|
CB, CC |
ADF drive problem |
|
CD |
BC RAM hardware |
|
CE |
BC RAM software |
|
CP |
Drive problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
E8 |
Jam in ADD (duplex) |
|
E9 |
Jam in pedestal |
|
EC, ED |
ADF jam |
|
EE |
ADF exit/reverse jam |
Toshiba 5110
|
Код ошибки |
Описание |
|
C0 |
Selector motor problems |
|
C2, C3 |
Processor to subprocessor communication problems |
|
C4 |
Paper feed cam motor drive problems |
|
C5 |
Optic system initialization error |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
C8 |
Scanner motor drive problems |
|
CD |
EPROM end of life |
|
CE |
EPROM defective or missing |
|
CF |
Development unit not properly installed or defective |
|
CP |
Main motor drive overloaded |
|
E0 |
Used toner collection bottle full |
|
E1 |
Paper jam in the machine |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Paper jam at start-up |
|
E4 |
Front cover open during the copy cycle |
|
E5 |
Cassette jam |
|
E6 |
Paper jam at by-pass or defective sensor |
Toshiba 5120
|
Код ошибки |
Описание |
|
C2 |
Signal to sub processor |
|
C4 |
Cam motor |
|
C5 |
Optics |
|
C7 |
Thermistor or fuser problem |
|
CD |
Weak battery |
|
CE |
Battery disconnected |
|
C0 |
DV select problem |
|
CP |
Drive |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam after turning on |
|
E4 |
Door opened during run |
|
E5 |
Lower cassette jam |
|
E6 |
Upper cassette |
Toshiba 5510
|
Код ошибки |
Описание |
|
C2 |
Signal to sub processor |
|
C4 |
Cam motor |
|
C5 |
Optics |
|
C7 |
Thermistor or fuser problem |
|
CD |
Weak battery |
|
CE |
Battery disconnected |
|
C0 |
DV select problem |
|
CP |
Drive |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam after turning on |
|
E4 |
Door opened during run |
|
E5 |
Lower cassette jam |
|
E6 |
Upper cassette |
Toshiba 5511
|
Код ошибки |
Описание |
|
C5 |
Initializing |
|
C6 |
Home switch |
|
C7 |
Thermistor |
|
C8 |
Scan motor on |
|
C9 |
Scan problem |
|
E0 |
Waste toner bag full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Exit jam |
|
E4 |
Front door |
Toshiba 5540
|
Код ошибки |
Описание |
|
A0 |
Abnormal signal received at the optional paper feed tray |
|
A1 |
Charge corona cleaner error |
|
A2 |
Duplex functional problems |
|
A3 |
Paper feed controller problems |
|
A4 |
Sorter problem |
|
A5 |
Communication lost with the sorter |
|
A6 |
Communication problems with the sorter interface |
|
A7 |
Communication problems with the feeder |
|
A9 |
Exposure lamp blown, or bad contacts |
|
C2, C3 |
Processor to subprocessor communication problems |
|
C5 |
Optic system initialization error |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
CB |
Original feed motor overloaded in the feeder |
|
CC |
Original transport motor overloaded in the feeder |
|
CE |
BC RAM firmware problems |
|
CF |
Toner density error |
|
CP |
Main motor drive overloaded |
|
E0 |
Used toner collection bottle full |
|
E1 |
Paper jam in the machine |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Paper jam at start-up |
|
E4 |
Front cover open during the copy cycle |
|
E5 |
Paper feed jam in the paper tray |
|
E8 |
Paper jam in the duplex unit |
|
E9 |
Paper jam in the optional paper feed unit |
|
EC |
Original misfeed in the feeder |
|
ED |
Original jam in the feeder |
|
EE |
Original jam at the feeder inverter or exit area |
Toshiba 5610, 5620
|
Код ошибки |
Описание |
|
C0 |
DV select switch or motor problem |
|
C1-C4 |
Signal from sub processor (motor control board) |
|
C5 |
Optics |
|
C6 |
Home sensor |
|
C7 |
Fuser |
|
C8 |
Scan |
|
CA |
Sub processor |
|
CD |
Weak battery |
|
CE |
Battery disconnected |
|
CP |
Main motor |
Toshiba 5910
|
Код ошибки |
Описание |
|
C2, C3 |
Processor to subprocessor communication problems |
|
C4 |
Paper feed cam motor drive problems |
|
C5 |
Optic system initialization error |
|
C7 |
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse |
|
C8 |
Scanner motor drive problems |
|
CD |
EPROM end of life |
|
CE |
EPROM defective or missing |
|
CF |
Development unit not properly installed or defective |
|
CP |
Main motor drive overloaded |
|
E0 |
Used toner collection bottle full |
|
E1 |
Paper jam in the machine |
|
E2 |
Paper jam in the fusing area |
|
E3 |
Paper jam at start-up |
|
E4 |
Front cover open during the copy cycle |
|
E5 |
Cassette jam |
|
E6 |
Paper jam at by-pass or defective sensor |
|
E7 |
Paper jam in the machine |
Toshiba 727, 728
|
Код ошибки |
Описание |
|
01 |
Scanner problem |
|
02 |
Paper jam or path switch |
|
03 |
Exit switch problem |
|
04 |
Jam or paper on drum |
|
05 |
Jam or false jam |
Toshiba 7610
|
Код ошибки |
Описание |
|
C2, C3 |
Board |
|
C4 |
Cam switch |
|
C5 |
Optics |
|
C7 |
Thermistor |
|
C8 |
Scan motor |
|
CD |
EEPROM dead |
|
CE |
EEPROM |
|
CP |
Drum motor |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Interlock |
|
E5 |
PF (lower cass.) |
|
E6 |
PF (upper cass.) |
Toshiba 7720
|
Код ошибки |
Описание |
|
A1 |
Spot motor |
|
A2 |
Duplex guide |
|
C0 |
Developer shift motor |
|
C2 |
Signal main board |
|
C3 |
Signal from main board |
|
C4 |
Cam switch |
|
C5 |
Optics have not moved |
|
C7 |
Thermistor or cold warm up |
|
C8 |
Scan motor |
|
CD |
Eprom dead |
|
CE |
Eprom |
|
CP |
Drum/fuser motor |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Interlock opened during copy cycle |
|
E5 |
Paper feed jam from lower cassette |
|
E6 |
Paper feed jam from upper cassette |
Toshiba 7812, 7815, 7816
|
Код ошибки |
Описание |
|
C5 |
Initializing |
|
C6 |
Home Switch |
|
C7 |
Thermistor |
|
C8 |
Scan motor |
|
C9 |
Scan problem |
|
CA |
Scan switch |
|
CC |
ADF motor |
|
E0 |
Waste toner bag full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Exit Jam |
|
E4 |
Front door |
Toshiba 7910
|
Код ошибки |
Описание |
|
C0 |
Paper feed cam switch problem |
|
C2 |
Bad signal to main board |
|
C3 |
Bad signal from main board |
|
C5 |
Optics |
|
C7 |
Fuser problem |
|
C8 |
Scan motor staying on |
|
CC |
Document feeder problem |
|
CE |
Battery or memory problem |
|
CP |
Drive |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Door was opened during job |
|
E5 |
Paper feed jam |
Toshiba 8412
|
Код ошибки |
Описание |
|
C0 |
Cam motor |
|
C1 |
Signal to color sub processor |
|
C2 |
Signal to black sub processor |
|
C3 |
Signal from color sub processor |
|
C4 |
Signal from black sub processor |
|
C5 |
Initializing |
|
C6 |
Scan home switch |
|
C7 |
Thermistor |
|
C8 |
Scan motor |
|
C9 |
Scan |
|
CA |
Document feeder |
|
CB |
Memory |
|
CC |
Document feeder |
|
CE |
Memory |
|
E0 |
Toner bag |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Exit jam |
|
E4 |
Front |
Toshiba 8510
|
Код ошибки |
Описание |
|
C0 |
Cam switches on cam motor |
|
C2 |
Bad signal to sub processor |
|
C3 |
Bad signal from sub processor |
|
C5 |
Scan does not initialize |
|
C7 |
Heater problem |
|
C8 |
Scan motor stays on |
|
CC |
ADF |
|
CD |
Weak battery in memory EPROM |
|
CE |
Memory disconnected |
|
CP |
Drive problem |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Door opened during copy |
|
E5 |
Feed jam |
Toshiba 8812
|
Код ошибки |
Описание |
|
C5 |
Initializing |
|
C6 |
Home switch |
|
C7 |
Thermistor |
|
C8 |
Scan motor on |
|
C9 |
Scan problem |
|
CA |
Scan Switch |
|
CC |
ADF motor on |
|
E0 |
Waste toner bag full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Exit Jam |
|
E4 |
Front door |
Toshiba 9110
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner problem |
|
A2 |
Duplex problem |
|
C0 |
Cam motor |
|
C1 |
Bad input to upper logic subprocessor |
|
C2 |
Bad input to lower logic subprocessor |
|
C3 |
Bad output from upper subprocessor |
|
C4 |
Bad signal from lower subprocessor |
|
C5 |
Optics problem at turn on |
|
C6 |
Scan home switch |
|
C7 |
Thermistor or fuser problem |
|
C8 |
Scan motor stays on |
|
C9 |
Scan problem |
|
CA |
Indicators |
|
CB |
Memory |
|
CC |
Motor stop signal present too long |
|
CE |
Software problem |
|
E0 |
Toner bag full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Exit jam |
|
E4 |
Door opened during run |
Toshiba 9230
|
Код ошибки |
Описание |
|
A1 |
Charge corona cleaner |
|
A2 |
Duplex problem |
|
C1 |
Board problem. Input to upper logic subprocessor |
|
C2 |
Board problem. Input to lower logic subprocessor |
|
C3 |
Board problem. Output to upper logic subprocessor |
|
C4 |
Board problem. Output to lower logic subprocessor |
|
C5 |
Optics locked or not initialized. Could be scan or lens mirror |
|
C6 |
Scan home switch |
|
C7 |
Fuser thermistor problem, or low temp |
|
C8 |
Scan motor won't shut off |
|
CA |
Indicators |
|
CB |
Memory |
|
CC |
Motor stop signal present too long |
|
CE |
Software |
|
C0 |
Paper feed cam motor problem |
|
E0 |
Waste toner full |
|
E1 |
Jam |
|
E2 |
Fuser jam |
|
E3 |
Jam |
|
E4 |
Front door was opened during copy run |
|
E5 |
Feed jam |
|
|
|
|