410039, г. Саратов, ул. Барнаульская д.11
Тел./факс: +7 ( 927) 161 – 36 - 65, 70-03-44
e-mail: remontprinterov@mail.ru
 |
|
Коды ошибок
копировальных аппаратов Konica
|
|
Konica 1015
|
Код ошибки
|
Описание
|
|
F09
|
Power leakage of some kind. Heat, exposure, AC or power supply.
|
|
F23
|
Toner motor
|
|
F26
|
Toner density adjustment problem. This means machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel that you should disconnect the toner motor first. This Код ошибки happens probably because either machine wasn't set up properly, or the customer kept on using the machine with the toner light on.
|
|
F28
|
Corona problem. Could be any corona. Must reset with "25: mode, "P45" set to "0"
|
|
F34
|
High fuser temperature
|
|
F35, F36
|
Low fuser temperature
|
|
F41
|
Scan home
|
|
F42
|
Scan home
|
|
F43
|
Exposure lamp
|
|
F45
|
Lens problem
|
|
F54
|
Fan motor
|
|
F60
|
ADF to main board communication problem
|
|
F67
|
ADF error
|
|
F77
|
Sorter gate
|
|
F88
|
AE adjustment problem
|
|
J11-J13
|
Feed jam
|
|
J16
|
Jam inside
|
|
J31, J32
|
Exit jam
|
|
J61, J62
|
ADF jam
|
|
J63
|
ADF exit jam
|
|
J72
|
Sorter jam
|
|
P20
|
Drum unit or toner level connection problem
|
|
P25
|
300 copies have been run since toner light came on. Depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
|
|
P26
|
Must adjust TDS in 47 mode
|
|
P64
|
ADF & operator are confused
|
|
P68, P69
|
ADF feed problem
|
|
P71
|
Sorter interlock
|
|
P81
|
Key counter not installed
|
Konica 1018
|
Код ошибки
|
Описание
|
|
F18
|
Paper lift did not complete
|
|
F23
|
Toner motor
|
|
F24
|
Pre clean lamp problem
|
|
F26
|
Toner density sensor
|
|
F34
|
Fuser overheat
|
|
F35
|
Fuser temperature too low. Lamp, thermofuse open wire
|
|
F36
|
Fuser temperature erratic. Probably thermistor
|
|
F41
|
End of scan sensor not actuated
|
|
F42
|
End of scan sensor not reached
|
|
F43
|
CVR (copy lamp voltage regulator)
|
|
F45
|
Lens or mirror movement problem
|
|
F52
|
Drive problem
|
|
F55
|
Zero cross.
|
|
F56
|
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
|
|
F60
|
ADF/machine interface problem
|
|
F67
|
ADF drive problem
|
|
F70
|
Sorter/machine interface problem
|
|
F77
|
Sorter bin problem
|
|
F78
|
Stapler problem
|
|
F86
|
Waste toner see 56
|
|
F98
|
Duplex problem
|
|
J11
|
Upper cassette
|
|
J12
|
Lower cassette
|
|
J13, J14
|
Paper feed jam
|
|
J15
|
Duplex unit jam
|
|
J16, J17
|
Feed jam
|
|
J19
|
Paper feed jam
|
|
J31, J32
|
Exit jam
|
|
J61
|
ADF opened during run
|
|
J62, J63
|
ADF jam
|
|
J65
|
RADF reverse jam
|
|
J72
|
Sorter jam, or sorter interlock opened
|
|
J75
|
Stapler jam
|
|
J92-J94
|
Duplex stack gate sensor or other duplex problem
|
|
J95
|
Duplex motor or duplex jam
|
|
P17
|
Right door
|
|
P19
|
Right door of paper feed unit
|
|
P20
|
Drum not installed properly or toner level sensor connection problem
|
|
P33
|
Left door
|
|
P61
|
RADF reverse cover open
|
|
P64
|
ADF was selected at the wrong time
|
|
P71
|
Sorter interlock
|
|
P74
|
Stapler overloaded, or paper left in stapler bin
|
|
P76
|
Out of staples
|
|
P81
|
Key counter not installed
|
|
P82
|
Memory card problem
|
|
P96
|
Paper in stacker when duplex selected
|
|
P97
|
Used bypass in duplex mode
|
|
P99
|
More than one side than the other in duplex
|
Konica 1112
|
Код ошибки
|
Описание
|
|
16
|
Feed jam
|
|
20
|
Toner level detector problem or loose connection
|
|
23
|
Toner feed problem
|
|
25
|
Toner. Means that 100 copies have been made since toner light came on
|
|
26
|
Toner density problem
|
|
31, 32
|
Exit jam
|
|
34
|
Fuser temperature too high
|
|
35
|
Fuser temperature too low
|
|
36
|
Fuser problem. Heat, thermistor, etc.
|
|
41
|
Scan return
|
|
42
|
Scan forward
|
|
43
|
Exposure lamp
|
|
50
|
Problem with IC8
|
|
52
|
EnКод ошибкиr (pulse sensor, PT; drive problem)
|
Konica 1120
|
Код ошибки
|
Описание
|
|
04
|
PTC heater. Don't know what this is, but "0" means it is not installed. 1 means it is.
|
|
F09
|
Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode" and select "P49" and reset to "0"
|
|
F23
|
Toner motor
|
|
F26
|
Toner density adjustment problem. This means the machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel you should disconnect the toner motor first. This Код ошибки happens probably because either the machine wasn't set up properly, or because the customer kept using the machine with the light on.
|
|
F28
|
Corona problem. Could be any corona.
|
|
F34
|
High fuser temperature.
|
|
F35, F36
|
Low fuser temperature.
|
|
F41, F42
|
Scan home
|
|
F43
|
Exposure lamp or exp. Lamp board.
|
|
F44
|
Lens drive problem.
|
|
F45
|
Lens problem.
|
|
F54
|
Fan motor.
|
|
F60
|
ADF to main board communication problem.
|
|
F67
|
ADF enКод ошибкиr (pulse sensor, drive problem)
|
|
F70
|
Sorter to machine communication problem.
|
|
F77
|
Sorter gate.
|
|
F88
|
AE adjustment problem.
|
|
J11-J13
|
Feed jam
|
|
J14-J16
|
Jam inside
|
|
J31, J32
|
Exit jam
|
|
J61, J62
|
ADF jam
|
|
J63
|
ADF exit jam
|
|
J72
|
Sorter jam
|
|
P11
|
Count. For total count, select "0". For developer count, select "5".
|
|
P12
|
Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.
|
|
P15
|
Size priority. 0 is standard. 1 is a size priority.
|
|
P16
|
Paper size priority.
|
|
P19
|
Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.
|
|
P20
|
Drum unit or toner level connection problem. Most likely, a loose connection.
|
|
P22-P24
|
Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
|
|
P25
|
300 copies have been run since toner light came on, depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
|
|
P26
|
ADF border erase. 0 for none. 5 for 5mm.
|
|
P26
|
Must replace and calibrate developer.
|
|
P27
|
PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
|
|
P27
|
Toner density sensor unplugged or toner density sensor problem.
|
|
P28
|
PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
|
|
P64
|
ADF & operator are confused. Remove original.
|
|
P68, P69
|
ADF feed problem.
|
|
P71
|
Sorter interlock.
|
|
P81
|
Key counter not installed.
|
Konica 1212
|
Код ошибки
|
Описание
|
|
04
|
PTC heater. Don't know what this is, but "0" means it is not installed. 1 means it is.
|
|
F09
|
Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode" and select "P49" and reset to "0"
|
|
F23
|
Toner motor
|
|
F26
|
Toner density adjustment problem. This means the machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel you should disconnect the toner motor first. This Код ошибки happens probably because either the machine wasn't set up properly, or because the customer kept using the machine with the light on.
|
|
F28
|
Corona problem. Could be any corona.
|
|
F34
|
High fuser temperature.
|
|
F35
|
Low fuser temperature.
|
|
F36
|
Low fuser temperature.
|
|
F41
|
Scan home
|
|
F43
|
Exposure lamp or exp. Lamp board.
|
|
F44
|
Lens drive problem.
|
|
F45
|
Lens problem.
|
|
F54
|
Fan motor.
|
|
F60
|
ADF to main board communication problem.
|
|
F67
|
ADF enКод ошибкиr (pulse sensor, drive problem)
|
|
F70
|
Sorter to machine communication problem.
|
|
F77
|
Sorter gate.
|
|
F88
|
AE adjustment problem.
|
|
J11-J13
|
Feed jam
|
|
J14-J16
|
Jam inside
|
|
J31, J32
|
Exit jam
|
|
J61, J62
|
ADF jam
|
|
J63
|
ADF exit jam
|
|
J72
|
Sorter jam
|
|
P11
|
Count. For total count, select "0". For developer count, select "5".
|
|
P12
|
Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.
|
|
P15
|
Size priority. 0 is standard. 1 is a size priority.
|
|
P16
|
Paper size priority.
|
|
P19
|
Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.
|
|
P20
|
Drum unit or toner level connection problem. Most likely, a loose connection.
|
|
P22-P24
|
Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
|
|
P25
|
300 copies have been run since toner light came on, depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
|
|
P26
|
ADF border erase. 0 for none. 5 for 5mm.
|
|
P26
|
Must replace and calibrate developer.
|
|
P27
|
PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
|
|
P27
|
Toner density sensor unplugged or toner density sensor problem.
|
|
P28
|
PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
|
|
P64
|
ADF & operator are confused. Remove original.
|
|
P68, P69
|
ADF feed problem.
|
|
P71
|
Sorter interlock.
|
Konica 1290, 1290RE
|
Код ошибки
|
Описание
|
|
16
|
Feed jam
|
|
20
|
Toner sensor connector
|
|
25
|
Toner light has been on for 100 copies
|
|
26
|
Toner density sensor
|
|
31
|
Exit switch not actuated
|
|
32
|
Exit jam
|
|
34
|
Fuser problem
|
|
35
|
Low fuser temperature
|
|
36
|
High fuser temperature
|
|
41
|
Scan did not return home
|
|
42
|
Scan problem
|
|
43
|
Exposure lamp problem
|
|
50
|
Board problem
|
|
52
|
Drive problem
|
|
85
|
No waste bottle
|
Konica 1590
|
Код ошибки
|
Описание
|
|
F23
|
Toner motor problem
|
|
F24
|
Pre-clean lamp
|
|
F26
|
Toner ratio
|
|
F34
|
High fuser temperature
|
|
F35
|
Low fuser temperature
|
|
F36
|
Thermistor
|
|
F41
|
Scan home
|
|
F42
|
Forward scan exposure lamp
|
|
F43
|
Exposure lamp
|
|
F45
|
Lens drive
|
|
F50
|
Board problem
|
|
F52
|
Drive
|
|
F77
|
Sorter bin sensor
|
|
J12, J13
|
Paper feed jam
|
|
J16
|
Paper feed jam
|
|
J31
|
Jam under drum
|
|
J32
|
Exit jam
|
|
J72
|
Sorter jam
|
|
P20
|
Drum not installed properly
|
|
P71
|
Sorter cover
|
Konica 1790
|
Код ошибки
|
Описание
|
|
F34
|
High fuser temperature
|
|
F35
|
Low fuser temperature
|
|
F36
|
Open thermistor or incomplete warm up
|
|
F41
|
Scan home problem
|
|
F42
|
Scan problem
|
|
F43
|
CVR board problem
|
|
F45
|
Lens drive
|
|
F52
|
Drive
|
|
F55
|
Zero cross problem
|
|
F67
|
ADF drive
|
|
F77
|
Sorter drive
|
|
J11
|
Upper cassette jam
|
|
J12
|
Lower cassette jam
|
|
J14
|
LCT jam
|
|
J16
|
Cassette jam
|
|
J31, J32
|
Jam under drum
|
|
J62, J63
|
ADF jam
|
|
J72
|
Sorter jam
|
|
P14
|
LCT open
|
|
P61
|
ADF up
|
|
P64
|
Original on glass
|
|
P69
|
ADF original jam
|
|
P71
|
Sorter cover open
|
|
P81
|
Key counter out
|
Konica 2020
|
Код ошибки
|
Описание
|
|
F18
|
Paper lift did not complete
|
|
F23
|
Toner motor
|
|
F24
|
Pre clean lamp problem
|
|
F26
|
Toner density sensor
|
|
F34
|
Fuser overheat
|
|
F35
|
Fuser temperature too low. Lamp, thermofuse open wire
|
|
F36
|
Fuser temperature erratic. Probably thermistor
|
|
F41
|
End of scan sensor not actuated
|
|
F42
|
End of scan sensor not reached
|
|
F43
|
CVR (copy lamp voltage regulator)
|
|
F45
|
Lens or mirror movement problem
|
|
F52
|
Drive problem
|
|
F55
|
Zero cross.
|
|
F56
|
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
|
|
F60
|
ADF/machine interface problem
|
|
F67
|
ADF drive problem
|
|
F70
|
Sorter/machine interface problem
|
|
F77
|
Sorter bin problem
|
|
F78
|
Stapler problem
|
|
F86
|
Waste toner see 56
|
|
F98
|
Duplex problem
|
|
J11
|
Upper cassette
|
|
J12
|
Lower cassette
|
|
J13, J14
|
Paper feed jam
|
|
J15
|
Duplex unit jam
|
|
J16, J17
|
Feed jam
|
|
J19
|
Paper feed jam
|
|
J31, J32
|
Exit jam
|
|
J61
|
ADF opened during run
|
|
J62, J63
|
ADF jam
|
|
J65
|
RADF reverse jam
|
|
J72
|
Sorter jam, or sorter interlock opened
|
|
J75
|
Stapler jam
|
|
J92-J94
|
Duplex stack gate sensor or other duplex problem
|
|
J95
|
Duplex motor or duplex jam
|
|
P17
|
Right door
|
|
P19
|
Right door of paper feed unit
|
|
P20
|
Drum not installed properly or toner level sensor connection problem
|
|
P33
|
Left door
|
|
P61
|
RADF reverse cover open
|
|
P64
|
ADF was selected at the wrong time
|
|
P71
|
Sorter interlock
|
|
P74
|
Stapler overloaded, or paper left in stapler bin
|
|
P76
|
Out of staples
|
|
P81
|
Key counter not installed
|
|
P82
|
Memory card problem
|
|
P96
|
Paper in stacker when duplex selected
|
|
P97
|
Used bypass in duplex mode
|
|
P99
|
More than one side than the other in duplex
|
Konica 2028
|
Код ошибки
|
Описание
|
|
F18
|
Paper lift did not complete
|
|
F23
|
Toner motor
|
|
F24
|
Pre clean lamp problem
|
|
F26
|
Toner density sensor
|
|
F34
|
Fuser overheat
|
|
F35
|
Fuser temperature too low. Lamp, thermofuse open wire
|
|
F36
|
Fuser temperature erratic. Probably thermistor
|
|
F41
|
End of scan sensor not actuated
|
|
F42
|
End of scan sensor not reached
|
|
F43
|
CVR (copy lamp voltage regulator)
|
|
F45
|
Lens or mirror movement problem
|
|
F52
|
Drive problem
|
|
F55
|
Zero cross
|
|
F56
|
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
|
|
F60
|
ADF/machine interface problem
|
|
F67
|
ADF drive problem
|
|
F70
|
Sorter/machine interface problem
|
|
F77
|
Sorter bin problem
|
|
F78
|
Stapler problem
|
|
F86
|
Waste toner see 56
|
|
F98
|
Duplex problem
|
|
J11
|
Upper cassette
|
|
J12
|
Lower cassette
|
|
J13, J14
|
Paper feed jam
|
|
J15
|
Duplex unit jam
|
|
J16, J17
|
Feed jam
|
|
J19
|
Paper feed jam
|
|
J31, J32
|
Exit jam
|
|
J61
|
ADF opened during run
|
|
J62, J63
|
ADF jam
|
|
J65
|
RADF reverse jam
|
|
J72
|
Sorter jam, or sorter interlock opened
|
|
J75
|
Stapler jam
|
|
J92-J94
|
Duplex stack gate sensor or other duplex problem
|
|
J95
|
Duplex motor or duplex jam
|
|
P17
|
Right door
|
|
P19
|
Right door of paper feed unit
|
|
P20
|
Drum not installed properly or toner level sensor connection problem
|
|
P33
|
Left door
|
|
P61
|
RADF reverse cover open
|
|
P64
|
ADF was selected at the wrong time
|
|
P71
|
Sorter interlock
|
|
P74
|
Stapler overloaded, or paper left in stapler bin
|
|
P76
|
Out of staples
|
|
P81
|
Key counter not installed
|
|
P82
|
Memory card problem
|
|
P96
|
Paper in stacker when duplex selected
|
|
P97
|
Used bypass in duplex mode
|
|
P99
|
More than one side than the other in duplex
|
Konica 2125
|
Код ошибки
|
Описание
|
|
F18
|
Paper feed lift problem
|
|
F18-3
|
LCT problem
|
|
F18-4
|
LCT problem
|
|
F28-1
|
Charge corona
|
|
F28-2
|
Transfer or separator corona
|
|
F34-1
|
High fuser temperature
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F36-2
|
Low fuser temperature
|
|
F41
|
Scan return problem
|
|
F42
|
Scan forward problem
|
|
F43
|
Exposure lamp board problem
|
|
F45
|
Lens home problem
|
|
F52
|
Main motor drive problem
|
|
F55
|
Zero cross of DC power supply
|
|
F60
|
Communication interruption between the machine and RADF
|
|
F67
|
RDH or RADF drive problem
|
|
F70
|
Communication problem between machine and sorter
|
|
F77
|
Sorter bin problem
|
|
F78
|
No memory card installed
|
|
F86
|
Too many copies were made after toner waste was full. Reset with 47 mode, Код ошибки 94.
|
|
F98
|
Duplex guide plate does not return home quickly enough
|
|
J10
|
Feed jam
|
|
J11
|
Upper feed jam
|
|
J12
|
Lower feed jam
|
|
J13
|
Upper paper feed unit jam
|
|
J14, J15
|
Lower paper feed unit jam
|
|
J16, J17
|
Jam in machine
|
|
J19
|
Paper feed unit jam
|
|
J21
|
Jam around drum
|
|
J31
|
Exit jam
|
|
J32
|
Exit jam
|
|
J61, J62
|
RDH/RADF jam or open
|
|
J63
|
RADF exit jam
|
|
J72
|
Sorter jam or open interlock
|
|
J74
|
Finisher problem
|
|
J75
|
Stapler problem
|
|
J92-J95
|
Duplex jam
|
|
P17
|
Right side door open
|
|
P19
|
Paper feed unit door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P68
|
Original removed during operation of RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
|
|
P76
|
Out of staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P82
|
Memory card not installed, not formatted to Konica specs, or no machine serial number registered on memory card
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Bypass was used or attempted during duplex.
|
|
P99
|
Too many reverse side copies during duplex
|
Konica 2130
|
Код ошибки
|
Описание
|
|
F18
|
Paper feed lift problem
|
|
F18-3
|
LCT problem
|
|
F18-4
|
LCT problem
|
|
F28-1
|
Charge corona
|
|
F28-2
|
Transfer or separator corona
|
|
F34-1
|
High fuser temperature
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F36-2
|
Low fuser temperature
|
|
F41
|
Scan return problem
|
|
F42
|
Scan forward problem
|
|
F43
|
Exposure lamp board problem
|
|
F45
|
Lens home problem
|
|
F52
|
Main motor drive problem
|
|
F55
|
Zero cross of DC power supply
|
|
F60
|
Communication interruption between the machine and RADF
|
|
F67
|
RDH or RADF drive problem
|
|
F70
|
Communication problem between machine and sorter
|
|
F77
|
Sorter bin problem
|
|
F78
|
No memory card installed
|
|
F86
|
Too many copies were made after toner waste was full. Reset with 47 mode, Код ошибки 94.
|
|
F98
|
Duplex guide plate does not return home quickly enough
|
|
J10
|
Feed jam
|
|
J11
|
Upper feed jam
|
|
J12
|
Lower feed jam
|
|
J13
|
Upper paper feed unit jam
|
|
J14
|
Lower paper feed unit jam
|
|
J15
|
Lower paper feed unit jam
|
|
J16, J17
|
Jam in machine
|
|
J19
|
Paper feed unit jam
|
|
J21
|
Jam around drum
|
|
J31, J32
|
Exit jam
|
|
J61
|
RDH/RADF jam or open
|
|
J62
|
RDH/RADF jam
|
|
J63
|
RADF exit jam
|
|
J72
|
Sorter jam or open interlock
|
|
J74
|
Finisher problem
|
|
J75
|
Stapler problem
|
|
J92-J95
|
Duplex jam
|
|
P17
|
Right side door open
|
|
P19
|
Paper feed unit door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P68
|
Original removed during operation of RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
|
|
P76
|
Out of staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P82
|
Memory card not installed, not formatted to Konica specs, or no machine serial number registered on memory card
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Bypass was used or attempted during duplex.
|
|
P99
|
Too many reverse side copies during duplex
|
Konica 2203
|
Код ошибки
|
Описание
|
|
F35
|
Low Temperature
|
|
F41, F42
|
Optics
|
|
F43
|
CVR
|
|
F46
|
Lens drive
|
|
F51
|
Door
|
|
F52
|
Drive
|
|
J11
|
Upper PF jam
|
|
J12
|
Lower PF jam
|
|
J13
|
Jam
|
|
J21
|
Separator jam
|
|
J31
|
Transport jam
|
|
J32
|
Jam
|
|
P81
|
Key counter
|
Konica 2290
|
Код ошибки
|
Описание
|
|
1
|
Sort jam
|
|
61
|
ADF/RADF open door
|
|
64
|
Original on glass
|
|
97
|
Duplex paper wrong size selected
|
|
99
|
Duplex fed double
|
|
F35, F36
|
Fuser
|
|
F41
|
Scan return
|
|
F42
|
Scan forward problem
|
|
F43
|
Exposure stays on
|
|
F46
|
Lens position problem
|
|
F52
|
Drive
|
|
F53
|
Developer unit shift problem
|
|
F67
|
ADF/RADF drive problem
|
|
F98
|
Duplex side to side gate problem
|
|
J11
|
Upper cassette jam
|
|
J12
|
Lower cassette jam
|
|
J13
|
LCT jam
|
|
J14
|
Jam
|
|
J15
|
Paper feed jam
|
|
J21
|
Jam under/around drum
|
|
J31
|
Transport jam
|
|
J32
|
Exit ajm
|
|
J61
|
RADF jam
|
|
J62
|
ADF
|
|
J63
|
ADF exit jam
|
|
J65
|
ADF
|
|
J72
|
Sort jam
|
|
J92-J96
|
Duplex jams
|
|
P81
|
Key counter
|
Konica 2590
|
Код ошибки
|
Описание
|
|
F34
|
High fuser temperature
|
|
F35
|
Low fuser temperature at warm up
|
|
F36
|
Low fuser temperature after warm up
|
|
F41
|
No scan
|
|
F42
|
No return scan
|
|
F43
|
Exposure lamp stays on
|
|
F45
|
Lens
|
|
F52
|
Drive
|
|
F55
|
Zero cross signal to main board
|
|
F67
|
ADF drive
|
|
F77
|
Sorter drive
|
|
F98
|
Duplex problem
|
|
J11
|
Bypass jam
|
|
J12
|
Middle cassette jam
|
|
J13
|
Lower cassette jam
|
|
J14
|
LCT jam
|
|
J15
|
Duplex jam
|
|
J16
|
Paper feed jam
|
|
J17
|
Registration jam
|
|
J31
|
Internal jam
|
|
J32
|
Exit jam
|
|
J61
|
ADF opened during runADF jam
|
|
J62, J63
|
ADF exit jam
|
|
J65
|
RADF jam
|
|
J72
|
Sorter jam
|
|
J92-J96
|
Duplex jams
|
|
P14
|
LCT cover open
|
|
P61
|
RADF cover open
|
|
P64
|
Original on glass
|
|
P69
|
RADF jam in sheet feet mode
|
|
P71
|
Sorter cover open
|
|
P81
|
Key counter
|
|
P96
|
Paper still in duplex tray
|
|
P97
|
Wrong size selected for duplex
|
|
P99
|
Duplex confused by double fed originals
|
Konica 3035
|
Код ошибки
|
Описание
|
|
F18
|
Paper lift did not complete
|
|
F23
|
Toner motor
|
|
F24
|
Pre clean lamp problem
|
|
F26
|
Toner density sensor
|
|
F34
|
Fuser overheat
|
|
F35
|
Fuser temperature too low. Lamp, thermofuse open wire
|
|
F36
|
Fuser temperature erratic. Probably thermistor
|
|
F41
|
End of scan sensor not actuated
|
|
F42
|
End of scan sensor not reached
|
|
F43
|
CVR (copy lamp voltage regulator)
|
|
F45
|
Lens or mirror movement problem
|
|
F52
|
Drive problem
|
|
F55
|
Zero cross
|
|
F56
|
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
|
|
F60
|
ADF/machine interface problem
|
|
F67
|
ADF drive problem
|
|
F70
|
Sorter/machine interface problem
|
|
F77
|
Sorter bin problem
|
|
F78
|
Stapler problem
|
|
F86
|
Waste toner see 56
|
|
F98
|
Duplex problem
|
|
J11
|
Upper cassette
|
|
J12
|
Lower cassette
|
|
J13, J14
|
Paper feed jam
|
|
J15
|
Duplex unit jam
|
|
J16, J17
|
Feed jam
|
|
J19
|
Paper feed jam
|
|
J31, J32
|
Exit jam
|
|
J61
|
ADF opened during run
|
|
J62, J63
|
ADF jam
|
|
J65
|
RADF reverse jam
|
|
J72
|
Sorter jam, or sorter interlock opened
|
|
J75
|
Stapler jam
|
|
J92-J94
|
Duplex stack gate sensor or other duplex problem
|
|
J95
|
Duplex motor or duplex jam
|
|
P17
|
Right door
|
|
P19
|
Right door of paper feed unit
|
|
P20
|
Drum not installed properly or toner level sensor connection problem
|
|
P33
|
Left door
|
|
P61
|
RADF reverse cover open
|
|
P64
|
ADF was selected at the wrong time
|
|
P71
|
Sorter interlock
|
|
P74
|
Stapler overloaded, or paper left in stapler bin
|
|
P76
|
Out of staples
|
|
P81
|
Key counter not installed
|
|
P82
|
Memory card problem
|
|
P96
|
Paper in stacker when duplex selected
|
|
P97
|
Used bypass in duplex mode
|
|
P99
|
More than one side than the other in duplex
|
Konica 3135
|
Код ошибки
|
Описание
|
|
F18
|
Paper feed lift problem
|
|
F18-3
|
LCT problem
|
|
F18-4
|
LCT problem
|
|
F28-1
|
Charge corona
|
|
F28-2
|
Transfer or separator corona
|
|
F34-1
|
High fuser temperature
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F36-2
|
Low fuser temperature
|
|
F41
|
Scan problem
|
|
F42
|
Scan forward problem
|
|
F43
|
Exposure lamp board problem
|
|
F45
|
Lens home problem
|
|
F52
|
Main motor drive problem
|
|
F55
|
Zero cross of DC power supply
|
|
F60
|
Communication interruption between machine and RADF
|
|
F67
|
RDH or RADF drive problem
|
|
F70
|
Communication problem between machine and sorter
|
|
F77
|
Sorter, finisher, or stapler problem
|
|
F86
|
Too many copies were made after toner waste was full
|
|
F98
|
Duplex problem
|
|
J10
|
Feed jam
|
|
J11, J12
|
Jam in machine
|
|
J13
|
LCT jam
|
|
J14
|
LCT jam
|
|
J15
|
Duplex feed jam
|
|
J16, J17
|
Jam in machine
|
|
J19
|
LCT jam
|
|
J21
|
Jam around drum
|
|
J31
|
Jam in machine
|
|
J32
|
Exit jam
|
|
J61, J62
|
RDH/RADF jam
|
|
J63
|
RADF exit jam
|
|
J72
|
Sorter jam or open interlock
|
|
J74
|
Finisher problem
|
|
J75
|
Stapler problem
|
|
J92
|
Duplex jam
|
|
J93
|
Duplex jam
|
|
J94
|
Duplex jam
|
|
J95
|
Duplex jam
|
|
P17
|
Paper feed door open
|
|
P19
|
LCT door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P64
|
RDH original width different with guide width
|
|
P68
|
Original removed during operation or RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
|
|
P76
|
No staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Wrong size paper during duplex
|
|
P99
|
Too many reverse side copies during duplex.
|
Konica 3240
|
Код ошибки
|
Описание
|
|
F10-1
|
Paper feed or duplex communication problem
|
|
F10-2
|
Paper feed or duplex communication problem
|
|
F10-3
|
Paper feed unit connection problem
|
|
F10-4
|
Internal temperature problem
|
|
F18-1
|
Upper feed lift problem
|
|
F18-2
|
Lower paper feed lift problem
|
|
F18-3
|
Upper paper feed lift problem
|
|
F18-4
|
Middle paper feed unit problem
|
|
F18-5
|
Lower paper feed unit lift problem
|
|
F28-1
|
Transfer separator corona
|
|
F28-2
|
Charge corona
|
|
F34-1
|
High fuser temperature or bad thermistor
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature or open thermistor
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F42-1
|
Scan forward problem
|
|
F42-2
|
Scan home problem
|
|
F42-3
|
Scan problem
|
|
F43-1
|
Exposure lamp board problem
|
|
F43-2
|
Exposure lamp board problem
|
|
F43-3
|
Exposure lamp board problem
|
|
F44-1
|
Optics communication problem
|
|
F45-1
|
Lens home problem
|
|
F45-2
|
Mirror home problem
|
|
F51-2
|
Main motor speed problem
|
|
F52-1
|
Cooling fan problem
|
|
F52-2
|
Suction (transport) fan problem
|
|
F52-4
|
Optics cooling fan problem (2 fans; could be either one)
|
|
F60
|
Communication interruption between machine and RADF
|
|
F67
|
RDH or RADF pressure home sensor or pressure motor.
|
|
F70
|
Communication problem between machine and sorter
|
|
F76
|
Stapler problem
|
|
F77
|
Sorter bin problem
|
|
F78
|
No memory card installed
|
|
F80
|
Communication problem between machine and weekly timer
|
|
F81
|
Communication problem between machine and memory card
|
|
F97
|
Duplex up down plate problem
|
|
F98
|
Duplex guide plate problem
|
|
F99
|
Duplex indexer problem
|
|
J10
|
Feed jam
|
|
J11
|
Upper feed jam
|
|
J12
|
Lower feed jam
|
|
J13
|
Upper paper feed unit jam
|
|
J14
|
Lower paper feed unit jam
|
|
J15
|
Duplex feed jam
|
|
J17
|
Jam in machine
|
|
J17-7
|
Jam at paper feed unit exit
|
|
J18
|
Jam in machine from middle tray of paper feed unit
|
|
J31, J32
|
Exit jam
|
|
J61
|
RADF opened during run, or other RADF jam
|
|
J62
|
RDH/RADF jam
|
|
J63
|
RADF feed jam
|
|
J72
|
Sorter jam or open interlock
|
|
J74
|
Finisher problem
|
|
J75
|
Stapler problem
|
|
J92
|
Reversal sensor jam
|
|
J97-1
|
Stacker entrance jam
|
|
J97-2
|
Stacker entrance jam
|
|
J98
|
Stacker entrance jam
|
|
P17
|
Right side door open
|
|
P19
|
Paper feed unit door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P68
|
Original removed during operation of the RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went to the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
|
|
P76
|
Out of staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P82
|
Memory card not installed, not formatted to Konica specs, or no machine serial # registered on memory card.
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Bypass was used or attempted during duplex
|
|
P99
|
Too many reverse side copies during duplex
|
Konica 3290
|
Код ошибки
|
Описание
|
|
51
|
Door open
|
|
64
|
Original still on glass
|
|
71
|
Sorter interlock
|
|
91
|
Duplex interlock
|
|
97
|
Incorrect mode selected
|
|
99
|
Duplex problem
|
|
F35
|
Fuser
|
|
F41
|
Scan return
|
|
F42
|
Scan
|
|
F43
|
Exposure lamp
|
|
F46
|
Lens drive
|
|
F52
|
Machine drive
|
|
F67
|
RADF
|
|
F98
|
Duplex unit
|
|
J11
|
Upper cassette jam
|
|
J12
|
Lower cassette jam
|
|
J13
|
LCT jam
|
|
J14
|
Paper feed jam
|
|
J15
|
Duplex jam
|
|
J21
|
Drum wrap jam
|
|
J31
|
Transport jam
|
|
J32
|
Fuser jam
|
|
J61
|
RADF cover
|
|
J62
|
RADF feed
|
|
J63
|
RADF exit
|
|
J65
|
RADF jam
|
|
J72
|
Sorter jam
|
|
J94-J96
|
Duplex jam or paper still in duplex unit
|
|
P81
|
Key counter
|
Konica 3340
|
Код ошибки
|
Описание
|
|
F10-1
|
Paper feed or duplex communication problem
|
|
F10-2
|
Paper feed or duplex communication problem
|
|
F10-3
|
Paper feed unit connection problem
|
|
F10-4
|
Internal temperature problem
|
|
F18-1
|
Upper feed lift problem
|
|
F18-2
|
Lower paper feed lift problem
|
|
F18-3
|
Upper paper feed lift problem
|
|
F18-4
|
Middle paper feed unit problem
|
|
F18-5
|
Lower paper feed unit lift problem
|
|
F28-1
|
Transfer separator corona
|
|
F28-2
|
Charge corona
|
|
F34-1
|
High fuser temperature or bad thermistor
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature or open thermistor
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F42-1
|
Scan forward problem
|
|
F42-2
|
Scan home problem
|
|
F42-3
|
Scan problem
|
|
F43-1
|
Exposure lamp board problem
|
|
F43-2
|
Exposure lamp board problem
|
|
F43-3
|
Exposure lamp board problem
|
|
F44-1
|
Optics communication problem
|
|
F45-1
|
Lens home problem
|
|
F45-2
|
Mirror home problem
|
|
F51-2
|
Main motor speed problem
|
|
F52-1
|
Cooling fan problem
|
|
F52-2
|
Suction (transport) fan problem
|
|
F52-4
|
Optics cooling fan problem (2 fans; could be either one)
|
|
F60
|
Communication interruption between machine and RADF
|
|
F67
|
RDH or RADF pressure home sensor or pressure motor.
|
|
F70
|
Communication problem between machine and sorter
|
|
F76
|
Stapler problem
|
|
F77
|
Sorter bin problem
|
|
F78
|
No memory card installed
|
|
F80
|
Communication problem between machine and weekly timer
|
|
F81
|
Communication problem between machine and memory card
|
|
F97
|
Duplex up down plate problem
|
|
F98
|
Duplex guide plate problem
|
|
F99
|
Duplex indexer problem
|
|
J10
|
Feed jam
|
|
J11
|
Upper feed jam
|
|
J12
|
Lower feed jam
|
|
J13
|
Upper paper feed unit jam
|
|
J14
|
Lower paper feed unit jam
|
|
J15
|
Duplex feed jam
|
|
J17
|
Jam in machine
|
|
J17-7
|
Jam at paper feed unit exit
|
|
J18
|
Jam in machine from middle tray of paper feed unit
|
|
J31, J32
|
Exit jam
|
|
J61
|
RADF opened during run, or other RADF jam
|
|
J62
|
RDH/RADF jam
|
|
J63
|
RADF feed jam
|
|
J72
|
Sorter jam or open interlock
|
|
J74
|
Finisher problem
|
|
J75
|
Stapler problem
|
|
J92
|
Reversal sensor jam
|
|
J97-1
|
Stacker entrance jam
|
|
J97-2
|
Stacker entrance jam
|
|
J98
|
Stacker entrance jam
|
|
P17
|
Right side door open
|
|
P19
|
Paper feed unit door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P68
|
Original removed during operation of the RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went to the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
|
|
P76
|
Out of staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P82
|
Memory card not installed, not formatted to Konica specs, or no machine serial # registered on memory card.
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Bypass was used or attempted during duplex
|
Konica 4045
|
Код ошибки
|
Описание
|
|
F18
|
Paper lift did not complete
|
|
F23
|
Toner motor
|
|
F24
|
Pre clean lamp problem
|
|
F26
|
Toner density sensor
|
|
F34
|
Fuser overheat
|
|
F35
|
Fuser temperature too low. Lamp, thermofuse open wire
|
|
F36
|
Fuser temperature erratic. Probably thermistor
|
|
F41
|
End of scan sensor not actuated
|
|
F42
|
End of scan sensor not reached
|
|
F43
|
CVR (copy lamp voltage regulator)
|
|
F45
|
Lens or mirror movement problem
|
|
F52
|
Drive problem
|
|
F55
|
Zero cross.
|
|
F56
|
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
|
|
F60
|
ADF/machine interface problem
|
|
F67
|
ADF drive problem
|
|
F70
|
Sorter/machine interface problem
|
|
F77
|
Sorter bin problem
|
|
F78
|
Stapler problem
|
|
F86
|
Waste toner see 56
|
|
F98
|
Duplex problem
|
|
J11
|
Upper cassette
|
|
J12
|
Lower cassette
|
|
J13, J14
|
Paper feed jam
|
|
J15
|
Duplex unit jam
|
|
J16, J17
|
Feed jam
|
|
J19
|
Paper feed jam
|
|
J31, J32
|
Exit jam
|
|
J61
|
ADF opened during run
|
|
J62, J63
|
ADF jam
|
|
J65
|
RADF reverse jam
|
|
J72
|
Sorter jam, or sorter interlock opened
|
|
J75
|
Stapler jam
|
|
J92-J94
|
Duplex stack gate sensor or other duplex problem
|
|
J95
|
Duplex motor or duplex jam
|
|
P17
|
Right door
|
|
P19
|
Right door of paper feed unit
|
|
P20
|
Drum not installed properly or toner level sensor connection problem
|
|
P33
|
Left door
|
|
P61
|
RADF reverse cover open
|
|
P64
|
ADF was selected at the wrong time
|
|
P71
|
Sorter interlock
|
|
P74
|
Stapler overloaded, or paper left in stapler bin
|
|
P76
|
Out of staples
|
|
P81
|
Key counter not installed
|
|
P82
|
Memory card problem
|
|
P96
|
Paper in stacker when duplex selected
|
|
P97
|
Used bypass in duplex mode
|
|
P99
|
More than one side than the other in duplex
|
Konica 4065
|
Код ошибки
|
Описание
|
|
11-1
|
Paper feed jam
|
|
11-10
|
RADF jam
|
|
11-11
|
Sorter jam
|
|
11-12
|
Sorter jam
|
|
11-2
|
Paper feed jam
|
|
11-3
|
Registration area jam
|
|
11-4
|
Paper jam around drum (drum wrap jam)
|
|
11-5
|
Jam in transport area
|
|
11-6
|
Exit jam or duplex exit jam
|
|
11-7
|
Duplex reversing sensor jam or duplex feed jam
|
|
11-8
|
Duplex jam
|
|
11-9
|
Duplex jam
|
Konica 4145
|
Код ошибки
|
Описание
|
|
F18
|
Paper feed lift problem
|
|
F18-3
|
LCT problem
|
|
F18-4
|
LCT problem
|
|
F28-1
|
Charge corona
|
|
F28-2
|
Transfer or separator corona
|
|
F34-1
|
High fuser temperature
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F36-2
|
Low fuser temperature
|
|
F41
|
Scan problem
|
|
F42
|
Scan forward problem
|
|
F43
|
Exposure lamp board problem
|
|
F45
|
Lens home problem
|
|
F52
|
Main motor drive problem
|
|
F55
|
Zero cross of DC power supply
|
|
F60
|
Communication interruption between machine and RADF
|
|
F67
|
RDH or RADF drive problem
|
|
F70
|
Communication problem between machine and sorter
|
|
F77
|
Sorter, finisher, or stapler problem
|
|
F86
|
Too many copies were made after toner waste was full
|
|
F98
|
Duplex problem
|
|
J10
|
Feed jam
|
|
J11, J12
|
Jam in machine
|
|
J13
|
LCT jam
|
|
J14
|
LCT jam
|
|
J15
|
Duplex feed jam
|
|
J16, J17
|
Jam in machine
|
|
J19
|
LCT jam
|
|
J21
|
Jam around drum
|
|
J31
|
Jam in machine
|
|
J32
|
Exit jam
|
|
J61, J62
|
RDH/RADF jam
|
|
J63
|
RADF exit jam
|
|
J72
|
Sorter jam or open interlock
|
|
J74
|
Finisher problem
|
|
J75
|
Stapler problem
|
|
J92-J95
|
Duplex jam
|
|
P17
|
Paper feed door open
|
|
P19
|
LCT door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P64
|
RDH original width different with guide width
|
|
P68
|
Original removed during operation or RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
|
|
P76
|
No staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Wrong size paper during duplex
|
|
P99
|
Too many reverse side copies during duplex.
|
Konica 4155
|
Код ошибки
|
Описание
|
|
F18
|
Paper feed lift problem
|
|
F18-3
|
LCT problem
|
|
F18-4
|
LCT problem
|
|
F28-1
|
Charge corona
|
|
F28-2
|
Transfer or separator corona
|
|
F34-1
|
High fuser temperature
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F36-2
|
Low fuser temperature
|
|
F41
|
Scan problem
|
|
F42
|
Scan forward problem
|
|
F43
|
Exposure lamp board problem
|
|
F45
|
Lens home problem
|
|
F52
|
Main motor drive problem
|
|
F55
|
Zero cross of DC power supply
|
|
F60
|
Communication interruption between machine and RADF
|
|
F67
|
RDH or RADF drive problem
|
|
F70
|
Communication problem between machine and sorter
|
|
F77
|
Sorter, finisher, or stapler problem
|
|
F86
|
Too many copies were made after toner waste was full
|
|
F98
|
Duplex problem
|
|
J10
|
Feed jam
|
|
J11
|
Jam in machine
|
|
J12
|
Jam in machine
|
|
J13, J14
|
LCT jam
|
|
J15
|
Duplex feed jam
|
|
J16, J17
|
Jam in machine
|
|
J19
|
LCT jam
|
|
J21
|
Jam around drum
|
|
J31
|
Jam in machine
|
|
J32
|
Exit jam
|
|
J61, J62
|
RDH/RADF jam
|
|
J63
|
RADF exit jam
|
|
J72
|
Sorter jam or open interlock
|
|
J74
|
Finisher problem
|
|
J75
|
Stapler problem
|
|
J92-J95
|
Duplex jam
|
|
P17
|
Paper feed door open
|
|
P19
|
LCT door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P64
|
RDH original width different with guide width
|
|
P68
|
Original removed during operation or RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
|
|
P76
|
No staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Wrong size paper during duplex
|
|
P99
|
Too many reverse side copies during duplex.
|
Konica 4255
|
Код ошибки
|
Описание
|
|
F18
|
Paper feed lift problem
|
|
F18-3
|
LCT problem
|
|
F18-4
|
LCT problem
|
|
F28-1
|
Charge corona
|
|
F28-2
|
Transfer or separator corona
|
|
F34-1
|
High fuser temperature
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F36-2
|
Low fuser temperature
|
|
F41
|
Scan problem
|
|
F42
|
Scan forward problem
|
|
F43
|
Exposure lamp board problem
|
|
F45
|
Lens home problem
|
|
F52
|
Main motor drive problem
|
|
F55
|
Zero cross of DC power supply
|
|
F60
|
Communication interruption between machine and RADF
|
|
F67
|
RDH or RADF drive problem
|
|
F70
|
Communication problem between machine and sorter
|
|
F77
|
Sorter, finisher, or stapler problem
|
|
F86
|
Too many copies were made after toner waste was full
|
|
F98
|
Duplex problem
|
|
J10
|
Feed jam
|
|
J11, J12
|
Jam in machine
|
|
J13, J14
|
LCT jam
|
|
J15
|
Duplex feed jam
|
|
J16, J17
|
Jam in machine
|
|
J19
|
LCT jam
|
|
J21
|
Jam around drum
|
|
J31
|
Jam in machine
|
|
J32
|
Exit jam
|
|
J61, J62
|
RDH/RADF jam
|
|
J63
|
RADF exit jam
|
|
J72
|
Sorter jam or open interlock
|
|
J74
|
Finisher problem
|
|
J75
|
Stapler problem
|
|
J92-J95
|
Duplex jam
|
|
P17
|
Paper feed door open
|
|
P19
|
LCT door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P64
|
RDH original width different with guide width
|
|
P68
|
Original removed during operation or RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
|
|
P76
|
No staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Wrong size paper during duplex
|
Konica 4290
|
Код ошибки
|
Описание
|
|
B81
|
Key counter
|
|
F36
|
CA
|
|
F41
|
Optics forward
|
|
F42
|
Optics return
|
|
F43
|
CVR
|
|
F45
|
Lens drive
|
|
F46
|
Magnification data
|
|
F47
|
Mode data
|
|
F52
|
Drive
|
|
F56
|
Data transfer (CPU)
|
|
F57
|
Data transfer (RADF & Control Board)
|
|
F59
|
Pressure cam
|
|
F67
|
RADF drive
|
|
F73
|
Bin alarm
|
|
F98
|
Duplex unit
|
|
J11
|
Upper cassette jam
|
|
J12
|
Middle cassette jam
|
|
J13
|
Lower cassette jam
|
|
J15
|
Duplex 2nd side PF jam
|
|
J16
|
Jam before drum
|
|
J21
|
Drum wrap jam
|
|
J31
|
Conveyance jam
|
|
J32
|
Exit jam
|
|
J44
|
Jam
|
|
J61
|
RADF open
|
|
J62
|
RADF feed jam
|
|
J63
|
RADF exit jam
|
|
J65
|
RADF reversal jam
|
|
J72
|
Sorter jam
|
|
J92
|
Duplex unit inlet jam
|
|
J93
|
Duplex unit reverse jam
|
|
J94
|
Duplex unit conveyance jam
|
|
J95
|
Duplex unit conveyance jam
|
|
P10
|
Cassette end
|
|
P51
|
Door open
|
|
P61
|
RADF door
|
|
P64
|
Paper in ADF
|
|
P71
|
Sorter door
|
|
P91
|
Duplex door
|
|
P96
|
Paper in ADF
|
|
P97
|
Wrong cassette selected in duplex
|
Konica 4345
|
Код ошибки
|
Описание
|
|
F18-1
|
Upper paper feed problem
|
|
F18-2
|
Lower paper feed problem
|
|
F18-3
|
Upper paper feed unit or LCT lift problem
|
|
F18-4
|
Lower paper feed unit or LCT lift problem
|
|
F23
|
Toner motor problem
|
|
F28-2
|
Transfer corona or toner motor problem
|
|
F34-1
|
High fuser temperature or bad thermistor
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature or open thermistor
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F36-2
|
Low fuser temperature
|
|
F41-1
|
Scan return problem
|
|
F41-2
|
Scan overrun problem
|
|
F41-3
|
Scan problem
|
|
F41-4
|
Glass detector problem
|
|
F42-1
|
Scan forward problem
|
|
F42-2
|
Scan home problem
|
|
F43
|
Exposure lamp board problem
|
|
F45-1
|
Lens home problem
|
|
F45-2
|
Mirror home problem
|
|
F49
|
Optics fan
|
|
F52
|
Main motor drive problem
|
|
F54
|
Cooling fan
|
|
F55
|
Zero cross. Could be upper tray limit sensor
|
|
F60
|
Communication problem between the machine and ADF
|
|
F67
|
ADF drive problem
|
|
F70
|
Communication problem between machine and sorter
|
|
F77-1
|
Sorter problem
|
|
F77-2
|
Sorter bin shift
|
|
F77-3
|
Sorter guide bar or vibration motor
|
|
F77-4
|
Stapler vibrator motor problem
|
|
F78
|
No memory card installed
|
|
F98
|
Duplex guide plate problem
|
|
J10
|
Feed jam
|
|
J11
|
Upper feed jam
|
|
J12
|
Feed jam
|
|
J13
|
Upper paper feed unit or LCT jam
|
|
J14
|
Lower paper feed unit or LCT jam
|
|
J15
|
Duplex feed jam
|
|
J16, J17
|
Jam in machine
|
|
J19
|
Jam in LCT
|
|
J21
|
Drum wrap jam
|
|
J31, J32
|
Exit jam
|
|
J61
|
RADF opened during run, or other RADF jam
|
|
J62
|
RADF feed jam
|
|
J63
|
RADF inversion jam
|
|
J72
|
Sorter jam
|
|
J75
|
Stapler problem
|
|
J92
|
Sorter jam
|
|
J93
|
Sorter problem
|
|
J94, J95
|
Duplex jam
|
|
P17
|
Right side door open
|
|
P19
|
Paper feed unit door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P68
|
Original removed during operation of RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in staple mode, or more than 25 copies per bin were attempted by the stapler
|
|
P76
|
Out of staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P82
|
Memory card not installed, not formatted to Konica specs, or no machine serial # registered on the memory card.
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Bypass was used or attempted during duplex.
|
|
P99
|
Too many reverse side copies during duplex.
|
Konica 4355
|
Код ошибки
|
Описание
|
|
F18-1
|
Upper paper feed problem
|
|
F18-2
|
Lower paper feed problem
|
|
F18-3
|
Upper paper feed unit or LCT lift problem
|
|
F18-4
|
Lower paper feed unit or LCT lift problem
|
|
F23
|
Toner motor problem
|
|
F28-2
|
Transfer corona or toner motor problem
|
|
F34-1
|
High fuser temperature or bad thermistor
|
|
F34-2
|
High fuser temperature
|
|
F35-1
|
Low fuser temperature or open thermistor
|
|
F35-2
|
Low fuser temperature
|
|
F36-1
|
Low fuser temperature
|
|
F36-2
|
Low fuser temperature
|
|
F41-1
|
Scan return problem
|
|
F41-2
|
Scan overrun problem
|
|
F41-3
|
Scan problem
|
|
F41-4
|
Glass detector problem
|
|
F42-1
|
Scan forward problem
|
|
F42-2
|
Scan home problem
|
|
F43
|
Exposure lamp board problem
|
|
F45-1
|
Lens home problem
|
|
F45-2
|
Mirror home problem
|
|
F49
|
Optics fan
|
|
F52
|
Main motor drive problem
|
|
F54
|
Cooling fan
|
|
F55
|
Zero cross. Could be upper tray limit sensor
|
|
F60
|
Communication problem between the machine and ADF
|
|
F67
|
ADF drive problem
|
|
F70
|
Communication problem between machine and sorter
|
|
F77-1
|
Sorter problem
|
|
F77-2
|
Sorter bin shift
|
|
F77-3
|
Sorter guide bar or vibration motor
|
|
F77-4
|
Stapler vibrator motor problem
|
|
F78
|
No memory card installed
|
|
F98
|
Duplex guide plate problem
|
|
J10
|
Feed jam
|
|
J11
|
Upper feed jam
|
|
J12
|
Feed jam
|
|
J13
|
Upper paper feed unit or LCT jam
|
|
J14
|
Lower paper feed unit or LCT jam
|
|
J15
|
Duplex feed jam
|
|
J16, J17
|
Jam in machine
|
|
J19
|
Jam in LCT
|
|
J21
|
Drum wrap jam
|
|
J31, J32
|
Exit jam
|
|
J61
|
RADF opened during run, or other RADF jam
|
|
J62
|
RADF feed jam
|
|
J63
|
RADF inversion jam
|
|
J72
|
Sorter jam
|
|
J75
|
Stapler problem
|
|
J92
|
Sorter jam
|
|
J93
|
Sorter problem
|
|
J94, J95
|
Duplex jam
|
|
P17
|
Right side door open
|
|
P19
|
Paper feed unit door open
|
|
P33
|
Exit door open
|
|
P51
|
Front door open
|
|
P61
|
RADF cover open
|
|
P64
|
RADF not opened to remove originals
|
|
P68
|
Original removed during operation of RADF
|
|
P69
|
Original didn't feed during RADF/RDH operation
|
|
P71
|
Sorter interlock
|
|
P74
|
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in staple mode, or more than 25 copies per bin were attempted by the stapler
|
|
P76
|
Out of staples
|
|
P78
|
Stapler not installed
|
|
P81
|
Key counter not plugged in
|
|
P82
|
Memory card not installed, not formatted to Konica specs, or no machine serial # registered on the memory card.
|
|
P86
|
No toner waste box
|
|
P91
|
Duplex unit pulled out
|
|
P96
|
Paper in duplex tray
|
|
P97
|
Bypass was used or attempted during duplex.
|
|
P99
|
Too many reverse side copies during duplex.
|
Konica 5080, 6090, 7490
|
Код ошибки
|
Описание
|
|
11-1
|
Paper feed jam
|
|
11-10
|
RADF jam
|
|
11-11
|
Sorter jam
|
|
11-12
|
Sorter jam
|
|
11-2
|
Paper feed jam
|
|
11-3
|
Registration area jam
|
|
11-4
|
Paper jam around drum (drum wrap jam)
|
|
11-5
|
Jam in transport area
|
|
11-6
|
Exit jam or duplex exit jam
|
|
11-7
|
Duplex reversing sensor jam or duplex feed jam
|
|
11-8
|
Duplex jam
|
|
11-9
|
Duplex jam
|
|
|
|
|